Do it yourself "Get It Right" – the correct preparation of the inner surface
During my 25 years of experience in working with my clients at home, I was not here for the many problems at home it-yourself enthusiasts will no doubt face, but unfortunately for some people, there is information, not enough to have to implement all the important activities.
What is the job I was asked, yes, for me is the most important part of the decoration, yes, you guessed it! "PREPARATION internet surfers!
In this article we will focus onsome "Within the space problem" issue in detail, as you try to use this to solve problems for you so that the work of decoration runs as smoothly as possible.
"Preparation" of ACES flaky and dusty:
A couple of times called "whiting", "lime wash", "colourwash" or "temperament"
to paint the old tradition of "glue, paint 'methods for the designers of the old days used to mix" dimensions "or" glue "with" a good football (soccer) and water to create soft, matte butdelicate surface treatments start date after the Second World War until 1960, and was largely spent on housing estates built in that period.
When very modern, as in all types of furniture in the room?
This, I believe, like many other home "DIY", the fans, is a severe headache, and if you are familiar with "temperament" you know what I mean, in many of the oldest houses in the UK and elsewhere in the world butBut few people today, recreates for its soft texture and warm colors, but for the modern home, can influence the temperature a bit 'of a nightmare.
Whichever method you use to decorate the surface, it seems to hold well, even emulsion tends to ring and disconnect, even if you are using, but this powder should be removed and cured before painting, wallpaper, texture or decoration in general.
Removing the cover will be a dusty surfaceDirty work, cover floors and furniture with dust sheets before you start, also had a dust mask, gloves and wear glasses!
1: dry scrape all loose material / paint scraper with a strong, if not possible, try to moisten the surface.
2: Use a bucket with hot water and soap and a sponge, wash off the dust from the surface, often changing the dirty water from the bucket to clean.
3: When and the ceiling is done in dry, rub your finger onsurface if there is no dust, pointing the finger, rinse the surface again.
4: The crop area is now very porous when dry, and should be sealed with a dilute solution of "PVA" mix bonding, follow the directions recommended on the container, "What porous surfaces, the next week we will look in depth in different areas and how to prepare properly.
There is also a sealer suitable stabilizer that can be purchased, and thiscan be used if you wish, please follow the instructions on the container to follow.
Sometimes the names are painted on the ceiling and a bit 'of paint does not stick to the surface, the method used is probably an oil-based "primer" that the primer is mixed with turpentine / white spirit to thin down undercoat, in so they can be "rolled" but it is believed that this thin consistency, sunk by the powder, the powder is based on the surface, "says the estate is readyretraining, but is not recommended because of the potential dangers of using an oil-based coating to the attic, and also the effects of smoking such as paint dry!
When dry scrape off the ceiling, it is possible that there are pieces of paint that will not move, it is washed with hot water first and leave the water in the sink for ten or fifteen minutes, then remove them if Get Loose Otherwise, when wet coat of glaze, texture and color is used, willBubbling same effect of calling and zinc on the surface, and then maybe slowly, forcing the coast these pieces that you thought was relevant.
Thank you for reading this article, and I hope that gave you information about your "area squamosa" We hope that from now know more about the inner surface preparation, the next time we need a little 'and examine in more detail "adequate preparation for a series of indoor surfaces "included!
As with all DIY jobs "always follow the manufacturer's recommendations, as indicated on the package through the use of their material, you should be careful when using equipment and a strong tool and also wear goggles, mask and gloves in case of need!
Tone Dale Above 2007
Comments