To create a room Storage warehouse construction
Let's start with the material needed to build this pilot project:
– Pressure treated skids (4×4)
– Pressure treated floor joists (2×4)
– Exterior grade plywood floor 3 / 4''
– Top plate, bottom plate, studs, headers, studs and edge trimmers, lamb rivets, girders, subfascia (2×4)
– T1-11 siding off 5 / 8''
– CDX roof sheathing 1 / 2''
– Band (1×4)
– Hook and trim (1×3)
– Drip edge 15 pounds and felt roof
– Asphalt shingles
-Galvanized nails
– Hinges and locks
– Paint or stain
Step.1.FRAME PLAN
Cut the two pressure control valves treated 4-5 meters long skids.Do 4s for the same two pressure-treated 2 by 4s on edge joists.Cut six floor joists up to 45 cm long and located between the edge of the joists , 16 cm in the center, secured with 16d nails. Place the frame on skids, the thickness seemed as if it required a square on the floor and beams nail skids.Cover frame with 3 / 4 inches withoutplywood.
The walls Step.2.BUILD
For the wall, you have to cut six meters in length upper and lower plates and to explain the studs 24 inches on wall studs center.The are 8 meters long, with their upper end inclined rear wall 18 degrees.Build and pen on the floor frames need refreshing.
For the front wall, rock, top plate to 6 feet long and two plates under each foot long.Mark a door 4-foot-wide wall studs and stud positions.Cut four to 81 (fourth) cm, plus two71 (1 / 2) cm long cut trimmer studs.Also two 51-inch long 2 by 4s, and an equally wide strips half an inch thick plywood as a spacer, and join in a header. Mount the wall and secure the head, and then add four points criple on top, as shown on the front wall front page.Secure on the floor and the necessary support.
Built on the side walls by 41 inches wide and flat top and bottom 81 (1 / 4) inches in length studs.Attach floor.When their sections of the wall are square and pretended to nailor screw the corners together.
Step.3.FRAME THE ROOF
The roof consists of two groups of four beams, resting on the front and back of the first four beams plates.Cut page.Toenail as indicated on the front of the upper panels of 2-4 per 24 inches.Then cutting wall stud to fit between the end beams and the top plate of each side wall.Next, cut in two with four subfascia length and attach the front ends of the beams.
The walls Step.4.ENCLOSE
Next cut pieces of T1-11 siding onconcerns front and sides, with the exception of cuts doors.Position wire timber with the bottom edge of the bar to do it with 8d galvanized nails every 8 cm.
Step.5.INSTALL THE ROOF
Use 1/2-inch CDX plywood sheathing crest 6d nails.Cut side (or rake), trim the exposed end of the shell and cut coats attach.Also and install the front fascia adaptation of the basic foundation for the side and drip edge rakes.Install15-pound roof felt and the application of shingles.
Step.6.ADD doors and trim
Using waste left over siding, build a pair of open doors to fit, trim it to one of 3s.Cut and install one of three trim along the front corners of the barn and back sides, just above and on either side of . cap through the door opening with wooden blocks or knives and Fit check should intimate side and about 1 / 2 cm of approval led bottom.Finally attachzip with the ribbon and add a door can close.
CURRICULUM: The framework for this small warehouse floor will rest on pressure treated rails instead of a fixed slope foundation.If your site or poor drainage, first digging the soil to a depth of 4 cm and replaced it with gravel then place your rails on that.Next floor, walls and roof frame at the top level of the platform and connect it with plywood siding and asphalt shingles.Finally, build and hang a single entrance and nice stuffwith a little 'trim.
PS: Enjoy your new barn to barn.
Comments